Merco Extreme Bond Tapes
Click for Merco Interactive Size Conversion Tool
Merco Cross References and COMPARISONS
Merco Current deals
Click to go to Merco Twitter Link
Click for Merco Home Page

baruch Hashem

Search Merco:

Search Box
Custom Search

Merco Extreme Bond
Specifications and
 Application Guide

Back to Merco Extreme Bond Product Page

  • Features:
     · High bond strength and excellent impact or shock absorption
     · Excellent U.V., solvent, & moisture resistance
     · Flexible, moldable, compressible for curve lines and filling gaps
     · Maintains bond through broad temperature range - -30°C to 80°C
  • Applications:
     · Window glazing/seaming for standard and high impact resistant glass (i.e. hurricane glass, bulletproof glass)
     · Attachment of dissimilar surfaces
     · Replacement of mechanical fasteners, rivets, bolts, screws, cement/glue
     · Bonding of name plates & decorative trim; vertical/horizontal blind fastening, trophy & auto business
     · Bonding/seaming of metal in electrical panels, HVAC units
  • Physical Properties:
    Peel Strength-Initial 160 oz/in. to 195 oz/in
    Peel Strength-Normal Dwell 170 oz/in. to 220 oz/in
    Peel Strength-30 mins @ 80°C 202 oz/in. to 229 oz/in
    Peel Strength-30 mins @ -30°C 141 oz/in. to 185 oz/in
    Heat aging              -Excellent
    Low Temp Aging    -Excellent
    Heat Impact             -5 cycles at various temps Excellent

    NOTE: The physical properties listed above are typical test results obtained from a series of laboratory tests and should not be used for the purpose of writing specifications. Before using this product, user shall determine the suitability of the product for his/her use; and user assumes all risks and liabilities in connection therewith.  All test procedures used are in accordance with ASTM and PSTC methods

Advantages of Merco MEB Bond Tape over Mechanical Fasteners

  • Ability to tolerate differentiate movement of up to 3 (three) times their thickness
  • Acrylic foam tape can compensate for most irregularities of surface structure
  • Resists corrosion (unlike metal on metal fasteners)
  • Solvent and moisture resistant (but not recommended for submersion)
  • Reduce Vibration
  • Reduction in number of sku's. One tape instead of many size fasteners

Application Guide

  • Generally, 4 (four) square inches of tape should be used for each pound of supported load, in a static state
  • 50/50 mix of isopropyl alcohol/water is recommended for cleaning surfaces before application. Surfaces should, of course, be dry
  • Temperature application range is best between 70F and 95F.  For applications at temperatures outside these parameters it is recommended bond be tested before signing off for final use.
  • 15 PSI of pressure is recommended for normal, even surface application
  • Strength is dependent on the amount of adhesive to surface contact. For better support, embossing, braying, rolling etc can be used.
  • At 70F, 50% of final bond strength will be achieved in the first 20 minutes. Maximum bond strength will be achieved 72-96 hours after application.
Merco takes these credit cards

We take this stuff seriously: click PRIVACY POLICY button

Merco Hackensack, Inc
P.O.Box 875, 201 Route 59  Hillburn, NY 10931
Phone:  845-357-3699 Fax: 845-357-3677

Click here to email Merco Tape
Merco Cross References and Comparisons page


Contents copyright Merco Tape/Merco Hackensack, Inc, 1995-2013. All rights reserved. No part of this site may be used without prior permission.
All  statements, technical information and recommendations contained on this site, or  in any of our literature, are based upon research and experience which we  believe to be reliable, but such information or recommendations shall not  constitute a warrantee of suitability. Determination of final qualifications for  any particular use rests solely with the ultimate end user.

Merco ABOUT US Merco TEAMS and Sponsorships Merco Fliers and CREATIVES Merco CONTACT US